MSDS 9100 Series

 

MATERIAL SAFETY DATA SHEET

SECTION I – CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME:

SOLACE SEMI-GLOSS LATEX WHITE

IDENTIFICATION NUMBER:

AM9100

DATE PRINTED: 10/10/01

PRODUCT USE/CLASS

SUPPLIER:

MANUFACTURER:

Davis-Frost, Inc. 3416 Candler’s Mountain Road Lynchburg, VA 24502

Davis-Frost, Inc. 3416 Candler’s Mountain Road Lynchburg, VA 24502

EMERGENCY TELEPHONE:

800-424-9300

EMERGENCY TELEPHONE:

800-424-9300

434-846-5277

434-846-5277

PREPARER: PV

PHONE: 434-846-5277

PREPARE DATE: 08/15/01

SECTION II – COMPOSITION/INFORMATION ON INGREDIENTS

WT. PERCENT --------- OCCUPATIONAL EXPOSURE LIMITS -----------

---------- CHEMICAL NAME ----------

CAS NUMBER IS LESS THAN TLV-TWA TLV-STEL PEL-TWA PEL-CEILING SKIN

PROPYLENE GLYCOL 57-55-6 5.0% NO INFO NO INFO NO

(See Section XI for abbreviation legend)

SECTION III – PHYSICAL DATA

BOILING RANGE :

365 – 372 F

VAPOR DENSITY :

Is heavier than air

ODOR :

MILD

WEIGHT PER GALLON :

10.5644

APPEARANCE :

WHITE

EVAPORATION RATE: :

Is slower than Ether

SOLUBILITY IN H20 :

YES

VOLATILE BY WEIGHT :

52.4%

VOLATILE BY FOL. :

66.4%

VOCS, lbs/gal :

0.85

VOCS, grams/ltr :

102

(See Section XI for abbreviation legend)

SECTION IV – FIRE AND EXPLOSION HAZARD DATA

FLASH POINT: 240 F

LOWER EXPLOSIVE LIMIT: 2.4%

(SETAFLASH CLOSED CUP)

UPPER EXPLOSIVE LIMIT: 17.4%

EXTINGUISHING MEDIA: CO2 DRY CHEMICAL FOAM

UNUSUAL FIRE AND EXPLOSION HAZARDS: WATER MAY BE USED TO COOL CLOSED CONTAINERS TO PREVENT PRESSURE BUILD-UP ANE POSSIBLE AUTOIGNITION OR EXPLOSION WHEN EXPOSED TO EXTREME HEAT. KEEP CONTAINERS TIGHTLY CLOSED.

SECTION IV – FIRE AND EXPLOSION HAZARD DATA (continued)

ISOLATE FROM HEAT, SPARKS, AND OPEN FLAME. CLOSED CONTAINERS MAY EXPLODE WHEN EXPOSED TO EXTREME HEAT. SPECIAL FIREFIGHTING PROCEDURES: FIRE FIGHTERS MUST WEAR SELF CONTAINED BREATHING APPARATUS OR AIR MASKS. CONTAINERS EXPOSED TO FIRE SHOULD BE KEPT COOL WITH WATER SPRAY.

SECTION V – HEALTH HAZARD DATA

EFFECTS OF OVER EXPOSURE: IF INHALED: MAY EFFECT THE BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE, NAUSEA AND POSSIBLE UNCONSCIOUSNESS. CAN CAUSE NASAL AND RESPIRATORY IRRITATION. EYE CONTACT: CAUSE IRRITATION, BURNS, BLURRED VISION AND REDNESS. SKIN CONTACT: CAUSES IRRITATION, BURNS AND DEFATTING. INGESTION: CAUSES GASTROINTESTINAL IRRITATION, VOMITTING & DIARRHEA. MEDICAL CONDITIONS PRONE TO AGGRAVATION BY EXPOSURE: UNKNOWN EMERGENCY AND FIRST AID PROCEDURES: IF INHALED: REMOVE TO FRESH AIR. IF NOT BREATHING, GIVE MOUTH TO MOUTH RESUSCITATION. IF BREATHING IS DIFFICULT, GIVE OXYGEN. CALL A PHYSICIAN. KEEP THE PERSON WARM. IN CASE OF CONTACT, IMMEDIATELY FLUSH EYES OR SKIN WITH PLENTY OF WATER FOR 15 MINUTES WHILE REMOVING CONTAMINATED CLOTHING AND SHOES. GET MEDICAL HELP. NEVER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON. IF SWALLOWED: DO NOT INDUCE VOMITTING. EFFECTS OF CHRONIC EXPOSURE: REPEATED AND PROLONGED OVEREXPOSURE TO SOLVENTS MAY CAUSE PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE. INTENTIONAL MISUSE AND INHALING THE CONTENTS MAY BE FATAL. LATEX PAINTS CONTAIN COMPARITIVELY SMALL AMOUNTS OF SOLVENTS. PRIMARY ROUTE(S) OF ENTRY: INHALATION

SECTION VI – REACTIVITY DATA

HAZARDOUS DECOMPOSITION PRODUCTS: SMOKE, ACID FUMES, CARBON MONOXIDE, CARBON DIOXIDE CONDITIONS TO AVOID: STORE INDOORS TO PROTECT FROM FREEZING. INCOMPATIBILITY: STRONG OXIDIZING AGENTS. NONE KNOWN. HAZARDOUS POLYMERIZATION: WILL NOT OCCUR UNDER NORMAL CONDITIONS. STABILITY: THIS PRODUCT IS STABLE UNDER NORMAL STORAGE CONDITIONS.

SECTION VII – SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: AVOID BREATHING SOLVENT VAPOR. ELIMINATE ALL SOURCES OF IGNITION. ENSURE ADEQUATE VENTILATION. WASTE DISPOSAL METHOD: USE ABSORBENT PADS, PAPERS OR INERT POWDERS SUCH AS CLAY TO SOAK UP THE LIQUID SPILLS. DISPOSE OF THE WASTE IN ACCORDANCE WITH LOCAL, STATE AND FEDERAL REGULATIONS.
SECTION VIII – SAFE HANDLING AND USE INFORMATION
RESPIRATORY PROTECTION: IF WORKPLACE EXPOSURE LIMIT OF PRODUCT OR ANY COMPONENT IS EXCEEDED (SEE SECTION II). USE A NIOSH/MSHA APPROVED RESPIRATOR. APPROVED FILTERS RECOMMENDED WHEN VENTILATION IS RESTRICTED. VENTILATION: PROVIDE SUFFICIENT MECHANICAL VENTILATION TO MAINTAIN EXPOSURE BELOW TLV. PROTECTIVE GLOVES: WEAR RESISTANT GLOVES SUCH AS NEOPRENE. EYE PROTECTION: CHEMICAL GOGGLES WITH SIDE SHIELDS OR FACE SHIELDS RECOMMENDED. OTHER PROTECTIVE EQUIPMENT: USE PROTECTIVE CREAMS WHERE SKIN CONTACT IS LIKELY. REMOVE AND WASH CONTAMINATED CLOTHING BEFORE REUSE. HYGENIC PRACTICES: WASH HANDS BEORE EATING OR SMOKING. SMOKE IN DESIGNATED AREAS ONLY.
SECTION IX – SPECIAL PRECAUTIONS
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: STORE IN A COOL, DRY AREA WITH VENTILATION SUITABLE FOR STORING MATERIALS SHOWN IN SECTION II. FIVE GALLON PAILS AND LARGER METAL CONTAINERS SHOULD BE GROUNDED WHEN MATERIAL IS TRANSFERRED. OTHER PRECAUTIONS: CONTAINERS OF THIS MATERIAL MAY BE HAZARDOUS WHEN EMPTIED. SINCE EMPTIED CONTAINERS RETAIN PRODUCT RESIDUES, ALL HAZARD PRECAUTIONS GIVEN IN THIS MSDS MUST BE OBSERVED.
SECTION X – HMIS RATINGS
HMIS RATINGS – HEALTH: 1	FLAMMABILITY: 0		REACTIVITY: 0
SECTION XI – OTHER REGULATIONS
PREVIOUS MSDS REVISION DATE: 05/15/01
LEGEND: N.A. – Not Applicable, N.E. – Not Established, N.D. – Not Determined

The information contained on this MSDS has been checked and should be accurate. However, it is the responsibility of the user to comply with all Federal, State, and Local laws and regulations.

Home - Paint Products - Microban Tech - About Davis-Frost - Microban & Healthcare - Where to find Solace