9000 SERIES SOLACEÔ LOW ODOR/LOW VOC EGGSHELL WITH
MICROBANâDESCRIPTION:
A premium low odor/low VOC acrylic latex eggshell finish for use on interior surfaces such as walls, ceilings and wood trim. A good choice for heavy traffic areas because it washes and wears better than flat finishes.LOW ODOR/LOW VOC:
This acrylic latex product is especially formulated to be low odor and low VOC. VOC’s (Volatile Organic Compounds) add to the odor of most paints and to air pollution.USES:
Use on properly prepared and primed interior surfaces of drywall, wood, plaster, masonry, and concrete block. This product is ideal for use in occupied areas such as schools, hospitals, restaurants, and office buildings where minimal VOC and low odor is important.MICROBANâ
This product contains MICROBANâ Built-in Protection, an antimicrobial agent which inhibits the growth of odor and stain causing bacteria, mold and mildew on the paint film. MICROBANâ additive is EPA registered and lasts the useful life of the paint film by guarding against discoloration and degradation caused by microorganisms. This product does not protect users or others against food-borne or disease-causing bacteria, and does not take the place of normal cleaning and disinfecting procedures. MICROBANâ and the MICROBANâ symbol are registered trademarks of the Microban Products Company, Huntersville, NC. For more information, visit www.Microban.com.VEHICLE TYPE:
Vinyl AcrylicSHEEN:
Low/EggshellSPREAD RATE
: 400 square feet per gallon on smooth, primed or sealed surfaces of similar colorDRYING TIME @ 75° F: To touch: 1 hour To recoat: 4 hours
THINNER:
If necessary, add up to ˝ pint of water per gallon.APPLICATION:
Stir thoroughly before using. Application may be by brush, roller or spray. Most types of spray equipment are acceptable for spray application. Always wear a respirator when spraying and protect yourself and your surroundings from spray mist.LIMITATIONS:
Do not apply when temperature is below 50° F. Do not use over old gloss or semi-gloss enamels unless gloss is dulled by sanding the old surfaces. Do not use outside, on floors, or in high temperature (above 160° F) areas such as radiators.COLOR:
White and Tint Bases. For custom tint colors see Millennium Custom Colors.AVAILABILITY:
Five-Gallon and Gallon Containers% SOLIDS BY VOLUME:
34.8% ± 2%% SOLIDS BY WEIGHT:
51.5% ± 2%V. O. C.:
46 grams/liter or .38 lbs/gallonSURFACE PREPARATION - GENERAL PRACTICE
For best adhesion, surfaces should be clean, dry, non-greasy and properly primed. Remove mildew, dirt, grease, loose rust, and loose scaling paint before painting. Sand glossy surfaces to a dull luster. Allow all recommended primers to dry thoroughly prior to painting.
In the recommendations below, certain steps must be universally taken to prepare surfaces for painting no matter what the substrate is. Therefore, it is to be understood that as situations warrant, the following steps must be taken to assure a quality painting job:
REMOVAL OF MILDEW -- Remove mildew with a commercially prepared solution or use: 5 oz. (2/3 cup) Trisodium Phosphate (TSP), 3 oz. (1/3 cup) detergent, 1 qt. household bleach and 3 qts. warm water which will make a little over one gallon.
SEALING KNOTS AND STAINS WHICH MAY BLEED THROUGH PAINT FILM – Spot prime knots or stained area with M77 oil-based or M88 acrylic stain blocker, let dry, then prime entire surface with appropriate primer. Woods subject to tannin bleedthrough (cedar, redwood, etc.) should be primed entirely with M77 or M88. If stains show through the primer coat, these areas should be primed again before finishing.
REMOVAL OF CONTAMINANTS – All contaminants, such as grease, oil, dirt, etc., which would interfere with either the adhesion or aesthetic appeal of the finish should be removed.
SURFACE PREPARATION AND PRIMING
NEW DRYWALL -- Repair construction defects and fill openings with spackling. Prime with 167 Latex Primer Sealer. Allow primer to dry thoroughly (at least 2 hours at 75° F). Scuff sand with fine sandpaper to remove raised nap. Apply two coats of finish paint.
PLASTER AND MASONRY -- Apply only to firm, fully cured and dust free plaster or masonry surfaces. Repair construction defects and fill openings with spackling. Prime with 167 Latex Primer Sealer. Allow primer to dry thoroughly (at least 2 hours at 75° F). Inspect for "dry spots" in plaster and if necessary, spot prime these areas. Apply two finish coats of paint.
CONCRETE BLOCK -- Repair construction defects and fill openings with spackling. Prime with 1051 Premium Masonry Block Filler. Use a brush, roller or trowel to work the block filler well into the concrete blocks. Allow the block filler to dry thoroughly (at least 8 hours at 75° F). For best results, block filler should be lightly sanded prior to topcoating. Apply two finish coats of paint.
NEW WOOD -- Repair construction defects and counter sink all nails. Prime with 167 Latex Primer Sealer. Allow undercoat to dry thoroughly (at least 2 hours at 75° F). Sand lightly with fine sandpaper to remove raised grain. Fill nail holes, knots, corners, etc. with latex caulk or wood putty. Apply two finish coats of paint.
METAL – On ferrous metal surfaces (ones that rust, like steel), the water in this product will cause rust spots to appear on surfaces not completely sealed with primer. Remove all loose mill scale, rust, dirt and old coatings with abrasive cleaning. Prime with 59 Red Oxide Primer. Allow primer to dry thoroughly (at least 24 hours at 75° F) before applying topcoats.
PREVIOUSLY PAINTED SURFACES -- Remove loose, flaking paint and sand glossy enamel surfaces to a dull sheen. Spot prime bare areas with the appropriate primer and allow to dry thoroughly. Apply two coats of finish paint.
PRECAUTIONS: PROTECT FROM FREEZING! Do not take internally. Close container after each use. KEEP OUT OF REACH OF CHILDREN!